The IGST 4_2 is planned to be run on the ETB with MEB EM2 on April 2018
ISM doc. to be delivered at MOC before
Procedure/sequence to be delivered at MOC before .
MEB EM2 with IDB 4.3.3 will be used on ETB during test, however the procedures/sequences must be written using the PFM IDB 4.3.3 version (indicating clearly where there are discrepancies between the two versions).
Presence of 1-2 max. people from RPW at ESOC during test is strongly recommended by MOC
...
List of RPW flight sequences (SQ) Excel files (one file per sequence), named as the sequence convention in the FOP Plan (FOPP) doc. The SQ files must be gathered by procedure (one directory per proceduce named as the procedure convention defined in the FOPP). The procedure directories must be grouped by type "FCP", "CRP" or "COM" (one directory per type).
The RPW ISM doc. in pdf format
The RPW MU updated with the procedure/sequences.
A readme README.rst text file providing information about the content of the packageand
a CHANGELOG.rst providing the changes history.
The name of the data package must be delivered as a zip file, named as: RPW_IGST4-2_DATAPACK_IssueXX_RevYY.zip, where XX and YY are the issue and revision of the data pack.
Main constraints
IGST RPW-related setup
The IGST will be run on the ETB with the RPW EM2.
In terms of command/control the RPW IDB (V4.3.3) is the same for EM1, EM2 and PFM, nevertheless the FDIR triggering threshold values can be different between the 3 models! This has to be taken account when validated the test results.
Moreover there is no SCM and PA-HF/ANT sensor on the ETB/RPW-EM2 setup, in consequence during the IGST:
Switching ON SCM shall be prohibited
BIAS HV shall be not ENABLE
BIAS current setting/sweeping/calibration shall not be performed
Switching ON PA HF shall be prohibited
Info
title
NOTE
According to Sylvain Lodiot (see comments at the bottom of the page) the corresponding prohibited TCs in the sequences must be clearly indicated with the [not for the EM2 on the ETB] comment.
Status of the data package
...
The table gives the list of critical sequences required to perform the IGST test.
Sequence name
Description
Category
Status
Comment
AIWF001A
From SAFE mode switch OFF the RPW prime power interface (UNIT_A and UNIT_B ) via OBCP.
Switch-off
In preparation
Nominal switch OFF via OBCP
Delivered
AIWF002A
From SAFE mode switch OFF the RPW prime power interface (UNIT_A and UNIT_B ) via manual.
Switch-off
Other OFF procedures
Delivered
In preparation
AIWF002B
Switch OFF the RPW prime power interface (UNIT_A) via OBCP from the SAFE mode
Switch-off
Other OFF procedures
Delivered
In preparation
AIWF010A
Boot RPW DBS in prime power interface (UNIT_A) via OBCP
Switch-on
Nominal switch ON via OBCP
Delivered
In preparation
AIWF011A
Boot RPW DBS in prime power interface (UNIT_A) via manual
Switch-on
Nominal switch ON via manual
Delivered
In preparation
AIWF030A
Boot RPW DAS from EEPROM1 (default), EEPROM2, RAM
Transition mode
Modes transition
Delivered
In preparation
AIWF031A
Enter SERVICE mode and switch on RPW equipment
Transition mode (nominal case)
In preparation
AIWF035A
Enter SERVICE mode
Transition mode
In preparation
AIWF035B
Enter in SCIENCE SURVEY_NORMAL submode
Nominal Switch On equipment
Delivered
AIWF032A
Configure HK period
Configuration DPU and DAS
Delivered
AIWF032B
Load DPU and DAS common parameters
Configuration DPU and DAS
Delivered
AIWF032C
Load DPU and DAS power parameters
Configuration DPU and DAS
Delivered
AIWF032D
Configure Bias High Voltage parameter
Configuration DPU and DAS
Delivered
AIWF032E
Configure parameters for monitoring temperature
Configuration DPU and DAS
Delivered
AIWF032F
Configure Waveform parameters
Configuration DPU and DAS
Delivered
AIWF032G
Configure SBM1 parameters
Configuration DPU and DAS
Delivered
AIWF032H
Configure SBM2 parameters
Configuration DPU and DAS
Delivered
AIWF032I
Configure SC potential computation algorithm
Configuration DPU and DAS
Delivered
AIWF032J
Clear HK counter
Configuration DPU and DAS
Delivered
AIWF032K
Enable HK parameter report generation
Configuration DPU and DAS
Delivered
AIWF035A
Transition mode
In preparation
AIWF035C
Enter in SCIENCE SURVEY_
BURST
NORMAL submode
Transition mode
In preparation
AIWF035D
Modes transition Science
Delivered
AIWF035B
Enter in SCIENCE SURVEY_
BACKUP
BURST submode
Transition mode
In preparation
AIWF035E
Enter in RPW STANDBY mode from any other mode (except OFF)
Transition mode
In preparation
AIWF035F
Modes transition Science
Delivered
AIWF035C
Enter in
Enter in
AIWF032A
SBM_DETECTION mode
Transition mode
In preparation
AIWF035G
Go to SAFE mode (DBS) with TC_DPU_RESET command
Transition mode
In preparation
Modes transition Science
Delivered
AIWF037A
Configure THR for the RPW SCIENCE SURVEY_NORMAL mode.
Configuration THR
In preparation
Delivered
AIWF032B
AIWF037B
Configure
the Bias (mode, and relay) for the RPW SCIENCE mode.
Configuration
In preparation
AIWF032C
Configure
THR for the RPW SCIENCE SURVEY_BURST mode.
Configuration THR
In preparation
Delivered
AIWF032D
Configure DPU and DAS + configure HK period
Configuration
In preparation
AIWF037C
Load calibration parameters for THR
Configuration THR
Delivered
AIWF038A
AIWF032E
Load common parameters of TDS
Configuration TDS
In preparation
AIWF038B
AIWF032F
Configuration of TDS
, LFR
for SBM1 mode
Configuration TDS
In preparation
AIWF038C
AIWF032G
Configuration of TDS
, LFR
for SBM2 mode
Configuration TDS
In preparation
AIWF038D
AIWF032H
Configure TDS LFM parameters
Configuration TDS
AIWF038E
Configure TDS for the RPW SCIENCE SURVEY_NORMAL mode.
Configuration
TDS
AIWF038F
Configure TDS for the RPW SCIENCE SURVEY_BURST mode
Configuration TDS
AIWF039A
Configuration of LFR for SBM1 mode
Configuration LFR
AIWF039B
Configuration of LFR for SBM2 mode
Configuration LFR
AIWF039C
In preparation
AIWF032I
Load calibration parameters for THR
Configuration
In preparation
AIWF032J
Load common parameters of LFR
Configuration LFR
In preparation
AIWF039D
AIWF032K
Configure
TDS
LFR for the RPW SCIENCE SURVEY_NORMAL mode.
Configuration LFR
In preparation
AIWF039E
AIWF032L
Configure LFR for the RPW SCIENCE SURVEY_
NORMAL
BURST mode.
Configuration LFR
In preparationConfigure TDS
AIWF040A
AIWF032M
Configure the Bias (mode, and relay) for the RPW SCIENCE
SURVEY_BURST
mode.
Configuration
In preparation
AIWF032N
Configure LFR for the RPW SCIENCE SURVEY_BURST mode.
Configuration
In preparation
AIWF032O
Configure the Bias sweeping
Configuration
Bias
AIWF041A
Enable Compression
Compression
AIWF041B
Disable Compression
Compression
AIWF042A
Switch the converter (CONV)
Switch On equipment
AIWF042B
BOOT LFR from EEPROM1 (default), EEPROM2 and RAM + Enabled Verif Boot
Switch On equipment
AIWF042C
BOOT THR from EEPROM1 (default), EEPROM2 and RAM + Enabled Verif Boot
Switch On equipment
AIWF042D
BOOT TDS from EEPROM1 (default), EEPROM2 and RAM + Enabled Verif Boot
Switch On equipment
AIWF042E
Switch ON BIAS
Switch On equipment
AIWF042F
PA Switch ON
Switch On equipment
AIWF042G
SCM switch ON
Switch On equipment
AIWF043A
Enter SERVICE mode
Enter SERVICE Mode
AIWF044A
Enter in SCIENCE SURVEY_BACKUP submode
Enter Science BACKUP Mode
AIWF045A
Enter in RPW STANDBY mode from any other mode (except OFF)
Enter STANDBY Mode
AIWF046A
Go to SAFE mode (DBS) with TC_DPU_RESET command
Enter SAFE Mode
In preparation
AIWF260A
Dump DPU memory (TC_DPU_DUMP_MEMORY - Service 6)
Memory dump (S6)
In preparation
In preparation
AIWF370A
Run a test connection (PUS, Service 17) with the TC_DPU_TEST_CONNECTION {ZIW00012} (i.e. "ping")
Ping
"ping" (PUS, Service 17)
Extra sequences (required for the E2E 0th test)
Additionally to the sequences above, the following sequences are not critical for shall not be run during the IGST, but are required to perform the E2E 0th test performed by the SOC (see RPW 0th E2E-0 TEST DATAPACK RELEASE for more details).
Sequence name
Description
Category
Status
Comment
AIWF033A
Internal Calibration for LFR
Calibration
In preparation
Delivered
AIWF033B
BIAS Calibration
Calibration
In preparation
Delivered
AIWF033C
Run THR internal calibration
Calibration
In preparation
Delivered
AIWF033D
Execute
Configure and execute the BIAS sweep
Calibration
In preparation
Delivered
AIWF034A
Dump LFR, TDS, THR parameters
Dump
In preparation
Delivered
AIWF036A
Configuration
Bias1 current
Configuration Bias Current
In preparation
AIWF036B
Configuration Bias2 current
Bias currents
Configuration Bias
Current
In preparation
AIWF036C
Configuration Bias3 current
Configuration Bias Current
In preparation
Currents
Delivered
ISM status
Version
Status
Comment
Checking
1.0
Delivered
Delivered with the datapack 1.0
1.1
In preparation (required updates due to changes in SQ between data pack 1.0 and 1.1)
Delivered
Delivered with datapack 1.1.
Does the ISM is consistent with the list of delivered sequences?
Does the ISM fully cover the delivered sequences (and transitions)?
1.2
Delivered
Delivered with datapack 1.2
To be delivered with datapack 1.1.
Data package delivery status
Version
Status
Delivery date
Comment
Checking
1.0
Delivered
Delivered to Sylvain Lodiot (MOC). See feedbacks in
Jira
server
jira-lesia.obspm.fr JIRA
serverId
cb08a004-0694-3237-bcb1-3125e3ed9bc0
key
ROCOPE-81
1.1
To be delivered
Delivered
Delivered to Sylvain Lodiot (MOC).
Is the new naming convention for the sequences compliant?
Does the list of sequences is consistent with what has been decided with the MOC?
Does the RPW UM is up-to-date?
Does the datapack is complete?
1.2
Delivered
Expected for 16
To be delivered
Delivered to Sylvain Lodiot (MOC). See feedbacks in