Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

This page gives information about the RPW Flight Procedures (RFP).



About the RPW Flight Procedures

According to the FOP, the flight procedures are divided into three categories: the Flight Control Procedures (FCP), the Contingency Recovery Procedures (CRP) and the Commissioning Procedures (COM).

The RPW procedures files are archived in the /Procedures folder of the https://gitlab.obspm.fr/ROC/OpsLib gitlab repository (restricted access). A test version of this repository is available in https://gitlab.obspm.fr/ROC/OpsLib-Test (restricted access).

For a list of the corresponding RPW Operating Configurations Plans (RPWConsROP), see RPW Operating Plans.

For each of these categories, a table lists is given with the following informationcolumns:

  • Name – Name of the procedure (according to the ESA convention)
  • Description
  • Configuration at start
  • - Short description of the procedure (to be reported into the info sheet of the Excel export)
  • State at start (i.e., initial ROP)
  • State at end (i.e., final ROP)Configuration at end
  • Author(s) – Entity that creates the procedure
  • Total duration – Total duration of the procedure execution in seconds (including the minimal time delay to be let after the last TC execution)
  • Minimal time delay at the end - Minimal time delay in seconds to be let at the end of the procedure )execution (i.e., to be let after the last TC execution)
  • Status – Status of the procedure writing (i.e., "DoneCurrent status (possible values are "To be done", "In progressProgress", "To Be Done", "GSE validatedValidated", "Added to FOP")
  • Any additional comments is given below. Note that the procedure file naming and format must comply the convention in SOL-ESC-IF-10002. It means that the file must be a Excel format file (.xls) with the procedure name as a file name.
  • To Be replaced")

Editing a procedure

The SOC provides to the instrument teams an online "Procedure Builder" than can be used to create/edit procedures. The site dedicated to RPW is available here. Nevertheless, the SOC cannot guarantee that this tool will be maintained during the whole mission, and the instrument teams are invited to develop and maintain their own tool. In the case of the ROC, the FIGARO tool, accessible via the MUSIC Web portal will replace at medium term the SOC procedure builder.


Warning
titleIMPORTANT

Please visit the operation guidelines page before editing a procedure!


Flight Control Procedures (FCP)

The table below gives the list of generic procedures, other than specific to the contingency recovery or commissioning operations (see next sections).The columns are:

Name –


Name
of the procedure (according to the ESA convention)
Description
- Short description of the procedure (to be reported into the info sheet of the Excel export)
  • Configuration at start – Initial RPWcon
  • Configuration at end – Final RPWcon
  • Author(s) – Entity that creates the procedure
  • Total duration – Total duration of the procedure in seconds (including the minimal time delay to be let after the last TC execution)
  • Minimal time delay at the end - Minimal time delay in seconds to be let at the end of the procedure execution (i.e., to be let after the last TC execution)
  • Status – Status of the procedure writing (i.e., "Done", "In Progress", "To Be Done", "Validated", "To Be replaced")
  • State at startState
    RPW_SCIENCE380RPW_SCIENCE
    NameDescriptionConfiguration at startConfiguration at endAuthor(s)Total duration (s)StatusComments

    IW-FCP-001


    RPW switch ON in SAFE mode using the prime/A interface for LCL and SpaceWireRPW_OFFRPW_SAFE_PRIME-A

    Unknown User (deconchy), Bernard Pontet


    Done
    IW-FCP-002RPW switch ON in SAFE mode using the prime/B interface for LCL and SpaceWireRPW_OFFRPW_SAFE_PRIME-B

    Unknown User (deconchy), Bernard Pontet


    Done
    IW-FCP-003Start DAS from EEPROM1 and transition to SERVICE modeRPW_SAFERPW_SERVICE

    Unknown User (deconchy), Bernard Pontet


    Done
    IW-FCP-004Start DAS from EEPROM2 and transition to SERVICE modeRPW_SAFERPW_SERVICE

    Unknown User (deconchy), Bernard Pontet


    Done
    IW-FCP-005Start DAS from RAM and transition to SERVICE modeRPW_SAFERPW_SERVICE

    Unknown User (deconchy), Bernard Pontet


    Done
    IW-FCP-006BOOT LFR from EEPROM1 + Disabled Verif BootRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-007BOOT THR from EEPROM1 + Disabled Verif BootRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-008BOOT TDS from EEPROM1 + Disabled Verif BootRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-009BOOT LFR from EEPROM2 + Disabled Verif BootRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-010BOOT THR from EEPROM2 + Disabled Verif BootRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-011BOOT TDS from EEPROM2 + Disabled Verif BootRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-012BOOT LFR from RAM + Disabled Verif BootRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-013BOOT TDS from RAM + Disabled Verif BootRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-014BOOT THR from RAM + Disabled Verif BootRPW_SERVICERPW_SERVICE
    Done

    IW-FCP-015

    Switch ON BIASRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-016Configure TDS, LFR and THR for the RPW_SCIENCE-NORMAL_DEFAULT config.RPW_SERVICERPW_SERVICE
    DoneIW-FCP-001 to be renamed to IW-FCP-009
    IW-FCP-017Configure the Bias for the RPW_SCIENCE-NORMAL_DEFAULT config.RPW_SERVICERPW_SERVICE
    DoneIW-FCP-002 to be renamed to IW-FCP-009
    IW-FCP-018Enter in RPW_SCIENCE-NORMAL_DEFAULTRPW_SERVICERPW_SCIENCE-NORMAL_DEFAULT
    DoneIW-FCP-003 to be renamed to IW-FCP-009

    IW-FCP-019

    Configure and execute the BIAS sweepRPW_SCIENCERPW_SCIENCE2501Done
    IW-FCP-020Free slot




    Replaced by IW-FCP-038. 020 slot id is free.
    IW-FCP-021 Internal Calibration for LFRRPW_SCIENCERPW_SCIENCE600Done
    IW-FCP-022Enter in RPW mode safeRPW_SCIENCERPW_SAFE
    Done
    IW-FCP-023PA Switch ONRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-024BIAS CalibrationRPW_SCIENCE380
    IW-FCP-025Enter in RPW_SURVEY-BURST_DEFAULTRPW_SCIENCERPW_SCIENCE-BURST_DEFAULT
    Done
    IW-FCP-026Switch on converterRPW_SAFERPW_SERVICE
    Done
    IW-FCP-027Enter in RPW_SURVEY-BURST_TDS_single_endedRPW_SCIENCE
    In progress
    IW-FCP-028Enter in RPW_SURVEY-BURST_TDS_dipoleRPW_SCIENCERPW_SCIENCE
    In progress
    IW-FCP-029Enter in RPW_SURVEY-BACKUP(through RPW Service mode)RPW_SERVICERPW_SCIENCE-BACKUP
    In progress
    IW-FCP-030Fix the current value on BIAS 1,2,3RPW_SCIENCERPW_SCIENCE
    Done
    IW-FCP-031Configure TDS, LFR and THR for the RPW_SCIENCE-BURST_DEFAULT configRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-032Configure DPU and DAS + configure HK periodRPW_SAFERPW_SERVICE
    Done
    IW-FCP-033SCM switch ONRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-034LOAD TDS, LFR common parametersRPW_SERVICERPW_SERVICE
    Done
    IW-FCP-035Configure TDS, LFR for sbm1 modeRPW_SERVICERPW_SERVICE
    done (temporary)
    IW-FCP-036Configure TDS, LFR for sbm2 modeRPW_SERVICERPW_SERVICE
    done (temporary)
    IW-FCP-037Configure TDS LFM parametersRPW_SERVICERPW_SERVICE
    done (temporary)
    IW-FCP-038 Configure internal Calibration for THRRPW_SERVICERPW_SERVICE
    done
    IW-FCP-039

    DUMP configurations and clear all the counters and statistic information in the DAS HK reports

    RPW_SERVICERPW_SERVICE
    done
    IW-FCP-XXXEnter in RPW STANDBY modeRPW_SAFERPW_STANDBY

    To be done
    IW-FCP-XXXEnter in RPW STANDBY modeRPW_STANDBYRPW_SAFE

    To be done
    IW-FCP-XXXEnter in RPW SERVICE mode from the RPW SCIENCE modeRPW_SCIENCERPW_SERVICE

    To be done

    Contingency Recovery Procedures (CRP)

    The table below gives the list of procedures specific to the contingency recovery operations.

    NameDescriptionConfiguration at startConfiguration at endAuthor(s)Creation dateStatusComments








    Commissioning Procedures (COM)

    The table below gives the list of procedures specific to the commissionning operations, including ANT and iBoom deployments, as well as the interference campaign.

    NameDescriptionConfiguration at startConfiguration at endAuthor(s)Creation dateStatusComments










    Action Items

    Action items relative to the flight procedures

    #DescriptionAssigneeCommentIssueDone
    1IW-FCP-021: TNR-HFR must be set in specific mag. config during the LFR calibration, in order to check B measurements


    •   
    2List the procedures that require formal parameters


    •   





    •