This page is dedicated to a summary of all existing TC. The purpose is to cross check their use in one (or more) sequence using the following table.
Moreover, performed tests are reported in this table also.
In green, the TC which are in a sequence already tested.
In yellow, the TC which are in a sequence untested yet.
The other lines contains TC which are not yet inside a sequence. Some of them will never been inside a sequence. in that case they should be put in red until they have been tested at least once.
TC Name | Belongs to the sequence named : | Tested during: | Using ETB version | Comments |
DPU_ENABLE_HK | ||||
DPU_OBC_ENABLE_HK | AIWF032K | IGST 4_2 | EM2 | |
LFR_ENABLE_HK | ||||
TDS_ENABLE_HK | ||||
THR_ENABLE_HK | ||||
DPU_S20_ENABLE_HK | ||||
DPU_DISABLE_HK | Disable DPU Housekeeping Parameter Report Generation. The command allows to disable one HK report at a time: the HK report is identified by its Structure ID. Pag. 185/236 DAS UM | |||
DPU_OBC_DISABLE_HK | ||||
LFR_DISABLE_HK | ||||
TDS_DISABLE_HK | ||||
THR_DISABLE_HK | ||||
DPU_S20_DISABLE_HK | ||||
DPU_UPDATE_HK_PERIOD | AIWF032A | IGST 4_2 | EM2 | |
DPU_OBC_UPDATE_HK_PERIOD | AIWF032A | IGST 4_2 | EM2 | |
LFR_UPDATE_HK_PERIOD | AIWF032A | IGST 4_2 | EM2 | |
TDS_UPDATE_HK_PERIOD | AIWF032A | IGST 4_2 | EM2 | |
THR_UPDATE_HK_PERIOD | AIWF032A | IGST 4_2 | EM2 | |
DPU_S20_UPDATE_HK_PERIOD | AIWF032A | IGST 4_2 | EM2 | |
DPU_ENABLE_EVENT | Enable Event Report Generation. The command allows to enable several event report. Each event is identified by its report ID. Pag. 225 DAS UM | |||
DPU_DISABLE_EVENT | Disable Event Report Generation. The command allows to disable several event report. Each event is identified by its report ID. Pag. 225 DAS UM | |||
DPU_LOAD_MEMORY | AIWF261A | IGST 4_2 | EM2 | |
LFR_LOAD_MEMORY | p196 DAS UM | |||
TDS_LOAD_MEMORY | p196 DAS UM | |||
THR_LOAD_MEMORY | p196 DAS UM | |||
DPU_DUMP_MEMORY | AIWF260A | IGST 4_2 | EM2 | |
DPU_DUMP_MEMORY | AIWF261A | IGST 4_2 | EM2 | |
LFR_DUMP_MEMORY | ||||
TDS_DUMP_MEMORY | ||||
THR_DUMP_MEMORY | ||||
DPU_CHECK_MEMORY | AIWF261A | IGST 4_2 | EM2 | |
LFR_CHECK_MEMORY | ||||
TDS_CHECK_MEMORY | ||||
THR_CHECK_MEMORY | ||||
DPU_TEST_CONNECTION | AIWF370A | IGST 4_2 | EM2 | |
DPU_ENABLE_SCIENCE | Enable DPU science TM transfer. Pag. 225 DAS UM | |||
LFR_ENABLE_SCIENCE | Enable DPU science TM transfer. Pag. 225 DAS UM | |||
DPU_PID5_ENABLE_SCIENCE | Enable DPU science TM transfer. Pag. 225 DAS UM | |||
TDS_ENABLE_SCIENCE | Enable DPU science TM transfer. Pag. 225 DAS UM | |||
DPU_PID6_ENABLE_SCIENCE | Enable DPU science TM transfer. Pag. 225 DAS UM | |||
THR_ENABLE_SCIENCE | Enable DPU science TM transfer. Pag. 225 DAS UM | |||
DPU_DISABLE_SCIENCE | Disable DPU science TM transfer. Pag. 225 DAS UM | |||
LFR_DISABLE_SCIENCE | Disable DPU science TM transfer. Pag. 225 DAS UM | |||
DPU_PID5_DISABLE_SCIENCE | Disable DPU science TM transfer. Pag. 225 DAS UM | |||
TDS_DISABLE_SCIENCE | Disable DPU science TM transfer. Pag. 225 DAS UM | |||
DPU_PID6_DISABLE_SCIENCE | Disable DPU science TM transfer. Pag. 225 DAS UM | |||
THR_DISABLE_SCIENCE | Disable DPU science TM transfer. Pag. 225 DAS UM | |||
DPU_SWITCH_OFF_EQUIPMENT | AIWF047B | Procedures ready to be tested. Switch off instrument separately. | ||
DPU_SWITCH_OFF_EQUIPMENT | AIWF047C | Procedures ready to be tested. Switch off instrument separately. | ||
DPU_SWITCH_OFF_EQUIPMENT | AIWF047D | Procedures ready to be tested. Switch off instrument separately. | ||
DPU_SWITCH_OFF_EQUIPMENT | AIWF047E | Procedures ready to be tested. Switch off instrument separately. | ||
DPU_SWITCH_OFF_EQUIPMENT | AIWF047F | Procedures ready to be tested. Switch off instrument separately. | ||
DPU_SWITCH_OFF_EQUIPMENT | AIWF047G | Procedures ready to be tested. Switch off instrument separately. | ||
DPU_SWITCH_OFF_EQUIPMENT | AIWF047H | Procedures ready to be tested. Switch off instrument separately. | ||
DPU_SWITCH_OFF_EQUIPMENT | AIWF047I | Procedures ready to be tested. Switch off instrument separately. | ||
DPU_SWITCH_OFF_EQUIPMENT | AIWF047K | Procedures ready to be tested. Switch off instrument separately. | ||
DPU_SWITCH_ON_EQUIPMENT | AIWF031A | IGST 4_2 | EM2 | Switch on converter in a large procedure |
DPU_SWITCH_ON_EQUIPMENT | AIWF042A | IGST 4_2 | EM2 | Switch on converter |
DPU_SWITCH_ON_EQUIPMENT | AIWF042E | IGST 4_2 | EM2 | Switch on Bias |
DPU_SWITCH_ON_EQUIPMENT | AIWF042F | Switch on PA. Procedure ready to be tested | ||
DPU_SWITCH_ON_EQUIPMENT | AIWF042G | Switch on SCM. Procedure ready to be tested | ||
DPU_RESET | AIWF046A | IGST 4_2 | EM2 | |
DPU_ENABLE_WATCHDOG | AIWF011A | IGST 4_2 | EM2 | |
DPU_DISABLE_WATCHDOG | Pag. 115 DAS UM | |||
DPU_BOOT_DAS | AIWF030A | IGST 4_2 | EM2 | |
DPU_BOOT_LFR | AIWF031A | IGST 4_2 | EM2 | |
DPU_BOOT_LFR | AIWF042B | IGST 4_2 | EM2 | |
DPU_BOOT_TDS | AIWF031A | IGST 4_2 | EM2 | |
DPU_BOOT_TDS | AIWF042D | IGST 4_2 | EM2 | |
DPU_BOOT_THR | AIWF031A | IGST 4_2 | EM2 | |
DPU_BOOT_THR | AIWF042C | IGST 4_2 | EM2 | |
DPU_DBS_LOAD_COMMON_PAR | Pag. 169 SSS UM . Need a procedure. Could be useful | |||
DPU_DAS_LOAD_COMMON_PAR | AIWF032B | IGST 4_2 | EM2 | |
DPU_LOAD_TEMP_PAR | AIWF032E | IGST 4_2 | EM2 | |
DPU_LOAD_POWER_PAR | AIWF032C | IGST 4_2 | EM2 | |
DPU_LOAD_SBM1_PAR | AIWF032G | IGST 4_2 | EM2 | |
DPU_LOAD_SBM2_PAR | AIWF032H | IGST 4_2 | EM2 | |
DPU_DBS_DUMP_PAR | Pag. 169 SSS UM . Need a procedure. Could be useful | |||
DPU_DAS_DUMP_PAR | AIWF032A | IGST 4_2 | EM2 | |
DPU_DAS_DUMP_PAR | AIWF032L | IGST 4_2 | EM2 | |
DPU_ENTER_STANDBY | AIWF045A | IGST 4_2 | EM2 | |
DPU_ENTER_SERVICE | AIWF031A | IGST 4_2 | EM2 | |
DPU_ENTER_SERVICE | AIWF043A | IGST 4_2 | EM2 | |
DPU_ENTER_SURVEY_NORMAL | AIWF035A | IGST 4_2 | EM2 | |
DPU_ENTER_SURVEY_BURST | AIWF035B | IGST 4_2 | EM2 | |
DPU_ENTER_SURVEY_BACKUP | AIWF044A | IGST 4_2 | EM2 | |
DPU_ENTER_SBM_DETECTION | AIWF035C | IGST 4_2 | EM2 | |
DPU_ENTER_SBM1_DUMP | This is a Debug TC. Nominally it is run by DPU. | |||
DPU_ENTER_SBM2_ACQ | This is a Debug TC. Nominally it is run by DPU. | |||
DPU_ENABLE_TRANS_MODE | Not enabled during flight. It is really needed? | |||
DPU_DISABLE_TRANS_MODE | Not enabled during flight. It is really needed? | |||
DPU_ENABLE_COMPRESSION | AIWF041A | Procedures ready to be tested. | ||
DPU_DISABLE_COMPRESSION | AIWF041B | Procedures ready to be tested. | ||
DPU_ENABLE_INFO_PKT | Pag. 175 DAS UM. Need a procedure. Could be useful | |||
DPU_DISABLE_INFO_PKT | Pag. 175 DAS UM. Need a procedure. Could be useful | |||
DPU_EXECUTE_BIAS_CMD | To run any generic BIAS TC Pag. 217 SSS. Need a procedure. Could be useful | |||
DPU_SET_BIAS1 | AIWF031A | IGST 4_2 | EM2 | |
DPU_SET_BIAS1 | AIWF033B | Procedures ready to be tested. | ||
DPU_SET_BIAS1 | AIWF036A | Procedures ready to be tested. | ||
DPU_SET_BIAS1 | AIWF042E | IGST 4_2 | EM2 | |
DPU_SET_BIAS2 | AIWF031A | IGST 4_2 | EM2 | |
DPU_SET_BIAS2 | AIWF033B | Procedures ready to be tested. | ||
DPU_SET_BIAS2 | AIWF036A | Procedures ready to be tested. | ||
DPU_SET_BIAS2 | AIWF042E | IGST 4_2 | EM2 | |
DPU_SET_BIAS3 | AIWF031A | IGST 4_2 | EM2 | |
DPU_SET_BIAS3 | AIWF033B | Procedures ready to be tested. | ||
DPU_SET_BIAS3 | AIWF036A | Procedures ready to be tested. | ||
DPU_SET_BIAS3 | AIWF042E | IGST 4_2 | EM2 | |
DPU_SET_BIAS_RELAY | AIWF031A | IGST 4_2 | EM2 | |
DPU_SET_BIAS_RELAY | AIWF033B | Procedures ready to be tested. | ||
DPU_SET_BIAS_RELAY | AIWF033D | Procedures ready to be tested. | ||
DPU_SET_BIAS_RELAY | AIWF040A | Procedures ready to be tested. | ||
DPU_SET_BIAS_RELAY | AIWF042E | IGST 4_2 | EM2 | |
DPU_SET_BIAS_RFREQ | Not implemented in our commands probably needed for calibration (mail Vaivads 23 mar and 3 May 2017). An example to test the TC is in email JMT 15/02/2018 attachment SFT CNES v3.3.xml. | |||
DPU_SET_BIAS_SWEEP | This procedure execute the BIAS sweep. We use the command start bias sweep to perform the Sweep. An example to test the TC is in email JMT 15/02/2018 attachment SFT CNES v3.3.xml. Should be tested independently (not in a sequence) | |||
DPU_SET_BIAS_MODE | AIWF031A | IGST 4_2 | EM2 | |
DPU_SET_BIAS_MODE | AIWF033B | Procedures ready to be tested. | ||
DPU_SET_BIAS_MODE | AIWF033D | Procedures ready to be tested. | ||
DPU_SET_BIAS_MODE | AIWF040A | Procedures ready to be tested. | ||
DPU_SET_BIAS_MODE | AIWF042E | IGST 4_2 | EM2 | |
DPU_SET_BIAS_MODE | AIWF047A | Procedures ready to be tested. | ||
DPU_SET_BIAS_PAGE | Selects the accessed register page. An example to test the TC is in email JMT 15/02/2018 attachment SFT CNES v3.3.xml | |||
DPU_EXECUTE_PDU_CMD | Generic telecommand controlling the PDU. An example to test the TC is in email JMT 15/02/2018 attachment SFT CNES v3.3.xml | |||
DPU_START_FROM_CONTEXT | According with the DAS UM this TC is not implemented. However, an example to test the TC is in email JMT 15/02/2018 attachment SFT CNES v3.3.xml | |||
DPU_LOAD_BIAS_SWEEP | AIWF033D | Procedures ready to be tested. | ||
DPU_START_BIAS_SWEEP | AIWF033D | Procedures ready to be tested. | ||
DPU_START_BIAS_CALIB | AIWF033Bbis | Bias calibration has been performed by sequentially reproducing the calibration steps. Procedures ready to be tested once validated by Bias team? | ||
DPU_RESET_TM_BUFFER | ||||
DPU_CLEAR_HK | AIWF032J | IGST 4_2 | EM2 | |
DPU_START_TEST | DAS UM pag. 297. Only for test purpose on ground. Shall not be include in a sequence | |||
DPU_STOP_TEST | DAS UM pag. 298. Only for test purpose on ground. Shall not be include in a sequence | |||
DPU_LOAD_WAVEFORM_PAR | AIWF032F | IGST 4_2 | EM2 | |
DPU_LOAD_SUN_DISTANCE | Useful ? If yes, shall be implemented in a particular sequence | |||
DPU_LOAD_BHV_PAR | AIWF032D | Procedures ready to be tested. | ||
DPU_CLEAR_BIAS_SWEEP | DAS UM pag. 261. Is it needed prior to load a new sweeping table? It is not clear on the DAS UM. | |||
DPU_SAVE_CONTEXT | According with the DAS UM this TC is not implemented. However, an example to test the TC is in email JMT 15/02/2018 attachment SFT CNES v3.3.xml | |||
DPU_LOAD_VSC_PAR | AIWF032I | IGST 4_2 | EM2 | |
DPU_LOAD_RWF_PAR | DAS UM pag. 182. I think it s really useful. Need a specific procedure ? | |||
LFR_RESET | LFR UM p23 : shall not be used. Shall be tested not in a sequence. | |||
TDS_RESET | No information in TDS UM ... probably the same than for LFR | |||
THR_RESET | No information in THR UM ... probably the same than for LFR | |||
LFR_LOAD_COMMON_PAR | AIWF033D | IGST 4_2 | EM2 | |
LFR_LOAD_COMMON_PAR | AIWF039C | IGST 4_2 | EM2 | |
TDS_LOAD_COMMON_PAR | AIWF038A | IGST 4_2 | EM2 | |
LFR_LOAD_NORMAL_PAR | AIWF039D | IGST 4_2 | EM2 | |
TDS_LOAD_NORMAL_PAR | AIWF038E | IGST 4_2 | EM2 | |
THR_LOAD_NORMAL_PAR_1 | AIWF037A | IGST 4_2 | EM2 | |
THR_LOAD_NORMAL_PAR_2 | ||||
THR_LOAD_NORMAL_PAR_3 | ||||
LFR_LOAD_BURST_PAR | AIWF039E | IGST 4_2 | EM2 | |
TDS_LOAD_BURST_PAR | AIWF038F | IGST 4_2 | EM2 | |
THR_LOAD_BURST_PAR_1 | AIWF037B | IGST 4_2 | EM2 | |
THR_LOAD_BURST_PAR_2 | ||||
THR_LOAD_BURST_PAR_3 | ||||
LFR_LOAD_SBM1_PAR | AIWF039A | IGST 4_2 | EM2 | |
TDS_LOAD_SBM1_PAR | AIWF038B | IGST 4_2 | EM2 | |
LFR_LOAD_SBM2_PAR | AIWF039B | IGST 4_2 | EM2 | |
TDS_LOAD_SBM2_PAR | AIWF038C | IGST 4_2 | EM2 | |
THR_LOAD_CALIBRATION_PAR | AIWF037C | IGST 4_2 | EM2 | |
LFR_DUMP_PAR | AIWF034A | IGST 4_2 | EM2 | |
TDS_DUMP_PAR | AIWF034A | IGST 4_2 | EM2 | |
THR_DUMP_PAR | AIWF034A | IGST 4_2 | EM2 | |
LFR_ENTER_MODE | ||||
TDS_ENTER_MODE | ||||
THR_ENTER_MODE | ||||
LFR_ENABLE_CALIBRATION | AIWF033A | Procedure ready to be tested | ||
THR_ENABLE_CALIBRATION | AIWF033C | Procedure ready to be tested | ||
LFR_DISABLE_CALIBRATION | AIWF033A | Procedure ready to be tested | ||
TDS_DUMP_NORMAL_TSWF | A sequence need to be written for on-flight operations | |||
TDS_DUMP_SBM2_TSWF | A sequence need to be written for on-flight operations | |||
TDS_PERFORM_DIAGNOSIS | ||||
TDS_LOAD_LFM_PAR | AIWF038D | IGST 4_2 | EM2 | |
LFR_LOAD_FBINS_MASK | ||||
LFR_LOAD_KCOEFFICIENTS | TC to be run durnig the i intercalibration phase | |||
LFR_DUMP_KCOEFFICIENTS | TC to be run durnig the i intercalibration phase | |||
LFR_LOAD_FILTER_PAR | TC to be run durnig the i intercalibration phase | |||
LFR_LOAD_FILTER_PAR |