This page gives information about the RPW Flight Procedures (RFP)
Introduction
According to the FOP, the flight procedures are divided into three categories: the Flight Control Procedures (FCP), the Contingency Recovery Procedures (CRP) and the Commissioning Procedures (COM). For each of these categories, a table lists the following information:
- Name of the procedure
- Description
- Configuration at start
- Configuration at end
- Author(s)
- Creation date
- Current status (possible values are "To be done", "In progress", "Done", "Validated", "Added to FOP")
- Any additional comments is given below. Note that the procedure file naming and format must comply the convention in SOL-ESC-IF-10002. It means that the file must be a Excel format file (.xls) with the procedure name as a file name.
The RPW procedures files are archived in the /Procedures folder of the https://gitlab.obspm.fr/ROC/OpsLib gitlab repository (restricted access). A test version of this repository is available in https://gitlab.obspm.fr/ROC/OpsLib-Test (restricted access).
For a list of the RPW Operating Configurations (RPWCons), see RPW Operating Configurations.
IMPORTANT
Please read the operation guidelines before editing a procedure!
The guidelines to write an flight procedures are available
Flight Control Procedures (FCP)
The table below gives the list of generic procedures, other than specific to the contingency recovery or commissioning operations (see next sections).
Name | Description | Configuration at start | Configuration at end | Author(s) | Creation date | Status | Comments |
---|---|---|---|---|---|---|---|
IW-FCP-001 | RPW switch ON in SAFE mode using the prime/A interface for LCL and SpaceWire | RPW_OFF | RPW_SAFE | Unknown User (deconchy), Bernard Pontet | Done | RP-FCP-001_Iss01Rev00 to be renamed in IW-FCP-001 | |
IW-FCP-002 | RPW switch ON in SAFE mode using the prime/B interface for LCL and SpaceWire | RPW_OFF | RPW_SAFE | Unknown User (deconchy), Bernard Pontet | Done | RP-FCP-002_Iss01Rev00 to be renamed in IW-FCP-002 | |
IW-FCP-003 | Start DAS from EEPROM1 and transition to SERVICE mode | RPW_SAFE | RPW_SERVICE | Unknown User (deconchy), Bernard Pontet | Done | RP-FCP-003_Iss01Rev00 to be renamed in IW-FCP-003 | |
IW-FCP-004 | Start DAS from EEPROM2 and transition to SERVICE mode | RPW_SAFE | RPW_SERVICE | Unknown User (deconchy), Bernard Pontet | Done | RP-FCP-004_Iss01Rev00 to be renamed in IW-FCP-004 | |
IW-FCP-005 | Start DAS from RAM and transition to SERVICE mode | RPW_SAFE | RPW_SERVICE | Unknown User (deconchy), Bernard Pontet | Done | RP-FCP-005_Iss01Rev00 to be renamed in IW-FCP-005 | |
IW-FCP-006 | Switch ON BIAS; BOOT LFR;BOOT THR; BOOT TDS from EEPROM1 | RPW_SERVICE | RPW_SERVICE | Unknown User (deconchy), Bernard Pontet | Done | RP-FCP-006_Iss01Rev00 to be renamed in IW-FCP-006 | |
IW-FCP-010 | Switch ON BIAS; BOOT LFR;BOOT THR; BOOT TDS from EEPROM2 | RPW_SERVICE | RPW_SERVICE | Unknown User (deconchy), Bernard Pontet | Done | RP-FCP-007_Iss01Rev00 to be renamed in IW-FCP-007 | |
IW-FCP-014 | Switch ON BIAS; BOOT LFR;BOOT THR; BOOT TDS from RAM | RPW_SERVICE | RPW_SERVICE | Unknown User (deconchy), Bernard Pontet | Done | RP-FCP-008_Iss01Rev00 to be renamed in IW-FCP-008 | |
IW-FCP-018 | Configure TDS, LFR and THR for the RPW_SCIENCE-NORMAL_DEFAULT config. | RPW_SERVICE | RPW_SERVICE | InProgress | IW-FCP-001 to be renamed to IW-FCP-009 | ||
IW-FCP-019 | Configure the Bias for the RPW_SCIENCE-NORMAL_DEFAULT config. | RPW_SERVICE | RPW_SERVICE | InProgress | IW-FCP-002 to be renamed to IW-FCP-009 | ||
IW-FCP-020 | Enter in RPW_SCIENCE-NORMAL_DEFAULT | RPW_SERVICE | RPW_SERVICE_SCIENCE-READY | Done | IW-FCP-003 to be renamed to IW-FCP-009 | ||
IW-FCP-021 | Configure and execute the BIAS sweep | RPW_SCIENCE-NORMAL_DEFAULT | RPW_SCIENCE-NORMAL_DEFAULT | In progress | |||
IW-FCP-022 | Internal Calibration for RPW | RPW_SCIENCE-NORMAL_DEFAULT | RPW_SCIENCE-NORMAL_DEFAULT | In progress |
Contingency Recovery Procedures (CRP)
The table below gives the list of procedures specific to the contingency recovery operations.
Name | Description | Configuration at start | Configuration at end | Author(s) | Creation date | Status | Comments |
---|---|---|---|---|---|---|---|
Commissioning Procedures (COM)
The table below gives the list of procedures specific to the commissionning operations, including ANT and iBoom deployments, as well as the interference campaign.
Name | Description | Configuration at start | Configuration at end | Author(s) | Creation date | Status | Comments |
---|---|---|---|---|---|---|---|